JEM-Sport JEM-Sport IAT Air Temperature Sensor Kit, 3/8 NPT JEM-Sport IAT (Inlet Air Temperature) Sensor Kits are perfect for vehicles using any standalone ECU that are not equipped from the factory with an intake air temperature sensor or have removed the factory MAF and need an air temperature sensor to replace... MSRP: Was: Now: $49.00
Link Link TCC04 4 Channel EGT to CAN Module Link TCC04 4 Channel EGT to CAN module, powered by CANchecked The TCC04 EGT to CAN module allows you to connect up to four Type-K thermocouples and send the values via CAN bus and/or monitor them directly on your wireless enabled device... MSRP: Was: Now: $250.00
Link Link TCC08 8 Channel EGT to CAN Module Link TCC08 8 Channel EGT to CAN module, powered by CANcheckedThe TCC08 EGT to CAN module allows you to connect up to eight Type-K thermocouples and send the values ​​via CAN bus and/or monitor them directly on your wireless enabled device... MSRP: Was: Now: $300.00
Link MIPS 150PSI Pressure Sensor 1/8 NPT Media Isolated 150PSI/10 Bar Pressure Sensor, 1/8 NPT The MIPS 150PSI/10 Bar Pressure Sensor features a durable stainless steel construction and is designed for compatibility with various fluids, including oil, petrol, and water. MSRP: Was: Now: $120.00
Link Link Ethanol Content Sensor Kit (ECS) Looking to run flex-fuel? Then the Ethanol Content Sensor is a must have. The Ethanol Content Sensor measures the ratio of ethanol to petrol in a flex fuel vehicle. This sensor also measures fuel temperature. Compatible with all current Link Wire-In and... MSRP: Was: Now: $240.00
Link Link DI Driver-4 Discover the next evolution in engine tuning with our advanced Direct Injection (DI) control module. The DI Driver-4 is a highly configurable, cost effective and integrated solution, designed to give you full control of most modern solenoid type direct... MSRP: Was: Now: $749.00
JEM-Sport JEM-Sport E-Connector and Pin Kit "E" Loom Do you want to pin your own wiring harness into your new Link Standalone ECU? Here is the connector and terminal pin kit for the Link E Loom connection. You may also be interested in our B Loom connector kit, HERE. MSRP: Was: Now: $39.99
Link 10m 4 Core CAN Wiring 10m 4 Core CAN Wiring. Useful for wiring in CAN Accessories. Four internal wires (White, Green, Red, Black) in a PVC outer jacket. Internal Wire Spec: FLRRY 0.5mm² (20 AWG) Outer Jacket Sepc: PVC, OD 6.1mm MSRP: Was: Now: $42.00
Link Automotive Wire Pack 50m (4 Colors) Details 50m pack of Automotive Wire (4 colours). 20m x Red10m x Black10m x Red/Green10m x Green Wire Spec: AVSS Thinwall 0.5mm² (20 AWG) MSRP: Was: Now: $47.00
Link Link CAN Keypad 15 Button + 2 Rotary Encoders Rugged 15 button CAN Keypad with interchangeable 15mm inserts (sold separately). Two rotary encoders with 16 Blue indicator LEDs each. Four additional analog inputs allow additional sensors/switches to directly connect to the CAN Bus network through the... MSRP: Was: Now: $599.00
Link Link RACEPAD - Steering Wheel CAN Keypad RacePad is the ultimate CAN-bus steering wheel button panel designed to elevate your racing experience to the next level. With 4 rotary knobs and 8 easy-to-reach buttons, RacePad is the ideal addition to any race car, enabling both professional drivers... MSRP: Was: Now: $999.00
Link LS Gen 3 to Gen 4 Cam Sensor Conversion Harness Adapter harness to run the Gen 4 front mounted under water pump Cam Sensor on the Gen 3 LS Engine. MSRP: Was: Now: $40.00
Link LS Gen 4 Knock Adapter Loom Intended for use with Link ECU terminated LS engine harness. Plug and play compatibility with Gen 4 Knock Sensors in factory location. MSRP: Was: Now: $60.00
Link LS Gen 3 Knock Adapter Loom • Intended for use with Link ECU terminated LS engine harness. Plug and play compatibility with factory Gen 3 Knock Sensor loom (located in the valley). MSRP: Was: Now: $25.00
Link LS Map Adapter Harness • Intended for use with Link ECU terminated LS engine harness. Plug and play compatibility for Gen 3 LS map sensors MSRP: Was: Now: $25.00
Link LS Drive By Wire Adapter Loom • Intended for use with Link ECU terminated LS engine harness. Plug and play compatibility for Gen 4 LS DBW throttle bodies. • This adapter loom terminates to Aux 9/10, 5v reference, sensor ground, AN5, and AN6 via the pre-wired DBW connector... MSRP: Was: Now: $45.00
Link Pressure Sensor (PS150) Oil or Fuel pressure 10 Bar/150psi 1/8” NPT Thread Includes plug and pin kit Technical Specs and WiringUp to 150 PSI above atmospheric pressure, cannot be used to read vacuum0.5v = 0bar / 0PsiG4.5v = 10 Bar / 145.03PsiG MSRP: Was: Now: $205.00
JEM-Sport JEM-Sport B-Connector and Pin Kit "B" Loom Do you want to pin your own wiring harness into your new Link Standalone ECU? Here is the connector and terminal pin kit for the Link B Loom connection. You may also be interested in our A Loom connector kit, HERE. MSRP: Was: Now: $39.99
JEM-Sport JEM-Sport A-Connector and Pin Kit "A" Loom Do you want to pin your own wiring harness into your new Link Standalone ECU? Here is the connector and terminal pin kit for the Link A Loom connection. You may also be interested in our B Loom connector kit, HERE. MSRP: Was: Now: $39.99
Link Link Combined Pressure and Temperature Sensor (CPTS) Two sensors in one - Combined 10 bar (145 psi) Liquid Pressure sensor and -40 to 140 deg C L Liquid Temperature sensor. Suitable for Diesel, gasoline, E85, engine oil, transmission oil Up to 10.0 bar (145PSI/1000kpa) Pressure Sensor for Liquid -40 to... MSRP: Was: Now: $165.00
Link Air Temp Sensor 1/8th NPT IAT Available with Aluminum or Steel bungs / Mounting bosses. Includes 2-pin Deutsch DTM connector kit Aluminium and steel weld in mounting bosses available 1/8" NPT Thread MSRP: Was: Now: $80.00 - $102.00
Link Link Three Channel Inductive Igniter -I3 This three channel igniter is suitable for electronic ignition applications. Required when using coils that don't have inbuilt igniters.Common uses include: wasted spark on 6 cylinder engines, coil-per-plug setups on 3 cylinder engines or using... MSRP: Was: Now: $160.00
Link E-throttle G4 - #G4RET Link's new G4+ external E-throttle (Drive by Wire) module works with Link's G4+ Storm, Kurofune and PlugIN ECUs to give you full control of your throttle setup, allowing a faster more precise throttle response. Replace your old mechanical throttle... MSRP: Was: Now: $340.00
Link E-Throttle Accelerator Pedal Module E-Throttle Accelerator Pedal Module Firewall mounted hanging design 16degree (~70mm) travel Redundant dual output potentiometers suitable for use with Electronic throttle bodies Includes 6 pin mating connector kit MSRP: Was: Now: $195.00
Link Electronic Throttle Body Kit - 82mm 82mm Electronic Throttle Body 82mm Bore size Dual potentiometer redundancy Bosch quality and performance Includes groove on inlet port flange Includes mating connector kit MSRP: Was: Now: $255.00
Link Electronic Throttle Body Kit - 54mm 54mm Electronic Throttle Body 54mm Bore size Dual potentiometer redundancy Bosch quality and performance Includes groove on inlet port flange Includes mating connector kit MSRP: Was: Now: $255.00
Link Boost Control Solenoid - 3 Port More boost? Of course and this 3 port boost control solenoid will help you do it. 3 port boost control solenoids are the go-to for the majority of boost control applications, they allow for precise control of boost and boost levels can be raised to... MSRP: Was: Now: $140.00
Link Boost Control Solenoid - 4 Port Thinking of turning up the boost to max? Then this 4 port boost control solenoid is perfect. It allows for precise boost control of up to 120PSI.4 port Boost control soldenoids are commonly used for big boost applications, boost levels can be raised as... MSRP: Was: Now: $160.00
Link Wideband O2 sensor (LSU49) This sensor can be used with all wide band controllers and ECU’s that support LSU 4.9 sensors. This includes: Link G4+/G4X Fury and G4+Thunder ECU’s – These have on-board LSU4.9 wide-band control. Link CAN-Lambda... MSRP: Was: Now: $125.00
Link Link CAN Lambda Link’s CAN Lambda is an easy to use CAN module that provides digital wideband sensor control via CAN bus and is compatible with leading aftermarket ECUs. If using the CAN Lambda with a G4+/G4X PlugIn ECU use a Link CANPCB cable to... MSRP: Was: Now: $365.00
Link O2 Bung & Plug Used to install LSU 4.9 Wideband O2 sensor. Includes weld on bung and plug. MSRP: Was: Now: $22.00
Link Link Exhaust Gas Temperature Probe Extreme Duty Fast Response EGT Temperature Probe Type K thermocouple probe Exposed sensing junction for fastest response Includes 316 SS adjustable compression fitting Stainless steel protected wires Designed for extreme engine test & racing... MSRP: Was: Now: $135.00
Link 5 Bar MAP Sensor (MAP5EU) The Link 5 Bar MAP sensor reads up to 5 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 4.0 Bar (or 58psi) of boost pressure. Includes Plug and Pins Mount via weld on bund, tapped hole or... MSRP: Was: Now: $200.00
Link 8 Bar MAP Sensor (MAP8EU) The 8 Bar MAP Variohm Eurosensor reads up to 7 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 7 Bar (or 101psi) of boost pressure. Includes Plug and Pins Push wire through connector;... MSRP: Was: Now: $220.00
Link 4 Bar MAP Sensor (MAP4) The Link 4 Bar MAP sensor reads up to 4 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 3.0 Bar (or 44psi) of boost pressure. The wiring pinout for this sensor is marked directly on the sensor... MSRP: Was: Now: $130.00
Link 3 Bar MAP Sensor (MAP3) This Link MAP sensor reads up to 3 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 2.0 Bar (or 29psi) of boost pressure. The wiring pinout for this sensor is indicated on the sensor. Includes... MSRP: Was: Now: $125.00
